Customer Reviews

4.95 out of 5
Write a Review
  • All Reviews (365)
  • Image (41)
  • Video (1)
  • All Star
    • All Star(365)
    • 5 Star(351)
    • 4 Star(11)
    • 3 Star(2)
    • 2 Star(1)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
  • Babis
    2019-11-05 09:17:15

    Very nice case for my Riden DPS5015 module

    Comments (1)
  • banglm
    2018-02-08 11:16:37

    The unit fits a 36V5A switched PSU (Product ID: 1161864), and a 50V5A controller (Product ID: 1062473) neatly. Efficient unit, at 12V 1A it is 73%, and at 3A it goes up to 82%. The PSU slides in the bottom half of the housing. To be able to use thick wires, I removed the DC connector and soldered the wires to the PSU print directly. I used one of the (intended) DC inputs for an earth pin , and the other one to accommodate the AC input (extra protected with crimp sleeve and Ty wrap). Finally, I put

    Comments (2)
  • GGregg
    2017-12-22 23:00:58

    Nice compact enclosure. I used crimp ring terminals instead of soldering the large wires to the fan board and I used crimp spade terminals on the switch to make it easier to replace the switch if it is ever necessary. I also used extra flat and star lock washers on the binding post connections.

    Comments (1)
  • murcod
    2018-03-13 19:43:38

    This case is nicely finished and looks very professional. Once I realised the instructions on how to assemble it all are on the product page (not supplied with the case) it was easy to get it all together. Fitting the slide on lid can be a bit of a challenge if you make the output power wires too short. I found sliding it on from the front was the easiest way. It would be better if it had fuse or circuit breaker protection for the input power.

  • banglm
    2017-07-14 10:40:46

    Together with (in my case) DP 50V 5 A module ,and a 36V 5A powersupply banggood nr 30809964, this gives a compact powersupply. The powersupply fits nicely in this housing, pcb slides in perfectly; the holes for the 2 output pins at the back can be used for 3p power lead (protected with extra sleeve, and ty-wrap at inside) and earth pin, see picture.

    Comments (8)
  • Popusi
    2019-04-06 18:35:47

    This housing fits nicely the DPS5015 modul, but if you buy the communication version of the modul, you will not have a hole for the USB micro connector, so be careful which case you choose. I had to drill the backplane to fit the USB output. The instructions on the product page does not indicate clearly, how should you position the rear ventillator, some pictures show it on the right, some on the left side. Not sure if placement is important from cooling point of view, but still, instructions were

  • effevee
    2017-07-05 07:31:46

    This is a beautiful case for the range of DPS buck power supplies. It contains a high quality aluminium case and all the necessary parts to make a 'cool' power supply. The instructions on the website show how to assemble it with minimum fuss. Great value for money and definitely an asset for the electronic enthusiast :)

    Comments (1)
  • Fludizz
    2018-07-29 14:12:21

    Bought this together with the DPS3005 and DC2416 (36V 5A). The housing is simple extruded aluminum and has a few slots to slide boards into. The housing perfectly fits the DC2416 power module together with the DPS3005 as show in the pictures. It was easy to adapt to a direct 240v AC Input. The housing itself is conductive if you sand off the paint. So to make it properly grounded and safer to use with 240v input, I sanded all surfaces that make contact with the other parts and attached a ground

  • Breezer
    2018-03-27 08:16:29

    This is a good case , the aluminium is nice and thick enough. Holes are neatly drilled screws fall flush on the outside. The case I received had a small dent in the corner of the top cover, but I put that part on the back and is hardly visible. The colour is a bit darker then the photo in the add shows and its even better in reality. I did modify the power entry in the back because I didn't like the 2 big banana connectors, so I fitted a female DC connector instead. It is not cheap, but the quality

  • jeever
    2018-02-09 08:02:17

    Het kastje dat u rond de DPS3003 moet bouwen wordt als bouwpakket geleverd en is van werkelijk uitmuntende kwaliteit. Een verademing vergeleken met de plexiglazen niemendalletjes waarin Chinese producten vaak worden geleverd. Bij dit pakket hoort een klein voorgemonteerd printje. De enige bedoeling van dit printje is de ingangsspanning van de voeding te reduceren tot 12 Vdc voor het voeden van de miniatuur ventilator.


    Go to page


    You might be interested in

    recommendation for you
    • US$7.99
    • US$2.99
    • US$4.23
    • US$4.99
    • US$27.99
    • US$3.49
    • US$4.99
    • US$8.99
    • US$3.99
    • US$5.99
    • US$4.08
    • US$9.99
    • US$1.99
    • US$37.99
    • US$1.99
    • US$3.99
    • US$9.99
    • US$61.99