Customer Reviews

4.65 out of 5
Write a Review
  • All Reviews (187)
  • Image (26)
  • Video (3)
  • All Star
    • All Star(187)
    • 5 Star(158)
    • 4 Star(11)
    • 3 Star(7)
    • 2 Star(4)
    • 1 Star(7)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
  • June-21 2017 11:32:26

    I have build 2 quads with the Star4 and wanted to try out the new Star3. Easy build, the RX pads are VERY tiny and behind the usb, i didnt see them at first. This one is slightly cheaper and makes for a very light build. I am going to do a full video review soon. Been running the StarF4 on my 5" for weeks with no issues. And the 3" pictured is my first used of the F3.

    Comments (6)
  • August-08 2017 18:09:36

    This F3 with OSD! Current and Bec's is great! Hooked it up with some HiKV motors 2306 2650Kv, and it performs great! But do remember, RED means PLUS on mounting holes not MINUS! USB is located in better place than on F4 version! It has buzzer and led and RX port. Also 5v out. Can't wait for 20x20 AIO version!!! At least with 18Amps!

    Comments
  • September-20 2017 19:06:26

    this little board is actually great for an all in one would love to see a 40a or even a 60a board in the future gives me a clean feed and osd works great

    Comments (1)
  • June-19 2017 16:45:29

    I've been having tons of trouble with my builds but this one did good. I broke it before putting it on by switching the lead to a pigtail, but was able to bond it with E6000 and it's holding so far. Dumb mistake -- don't be like me, start with a pigtail connection. It's a great board that I was able to make fly immediately and it feeds plenty of power into the brother hobby 1407 on 4s. Such a beast...

    Comments
  • October-09 2017 10:42:23

    super clean build works well whit bf 3.2 and t1 tornado 1407 motors i use 8k/4K dynamic filter and dshot600 and are super smooth!

    Comments (1)
  • December-05 2017 16:06:01

    these are great value and this one works perfect for me, have been using now for one month, only couple of things to be aware of small solder pads for camera, receiver and video tx, not a problem if you take care no sd card , don't use anyway so no problem for me I am running vtx03 , camera micro and micro receiver all from the linear voltage regs with no problem, but be careful not to overload them!! will use again unless something better comes out highly recommended

    Comments
  • October-05 2018 20:30:55

    Funcionando a la perfección, noto que se calientan los variadores pero por ahora funciona bien

    Comments
  • May-15 2018 10:31:08

    Everything worked. Solder ports for video and sbus are small just be careful and hit glue after to keep from touching.

    Comments
  • July-18 2017 09:05:09

    Have all the functions but maybe low on UARTs :). Very convenient to use for small and clean builds. Don't like the fact that mounting holes go to VBAT but not a big no no.

    Comments
  • May-29 2018 11:11:44

    I Love these AIO flight controllers I have 3 of the F4 and this is my first F3 So easy to build and I think the F3 has a better location for the usb port.

    Comments
Show:

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$73.20
    • US$13.90
    • US$74.22
    • US$8.59
    • US$24.99
    • US$20.99
    • US$26.99
    • US$25.99
    • US$16.05
    • US$23.99
    • US$45.99
    • US$12.99
    • US$9.07
    • US$3.59
    • US$9.07
    • US$3.25
    • US$2.99
    • US$4.27