All Messages

Q: Where can i get the software to use the bluetooth mode?

Asked by Andrés Arturo Ariza Henríquez on 2018-08-27 04:38:33

1nformatica The app can be downloaded using the QR code on the front of the manual. See my review in the video section.

2020-09-19 02:57:37 Helpful (0)
Submit
Answers (1)
1nformatica 2020-09-19 01:34:41
1
Recommendations
Comments (0)

Top reviewers you may like:

1nformatica 2020-09-16 04:36:54
1
Recommendations
Comments (0)

Top reviewers you may like:

1nformatica The only difference I am aware of is that it is blue!

2020-09-02 02:37:25 Helpful (0)
Submit
Answers (1)

Q: Can I run this of a 12v 200w 16.66A bench top power supply ?

Asked by BG221839543 on 2020-08-25 10:45:08

1nformatica No. Spot welding needs much higher instantaneous current. Recommended are : 1. 20-45ah Lead-acid battery with good performance and small internal resistance 2. 3.5-5.5ah 45C 3S aeromodel lithium battery pack 3. 30-35ah capacity 18650 battery pack

2020-08-26 01:48:40 Helpful (0)
Submit
Answers (2)
1nformatica 2020-08-17 04:45:12
1
Recommendations
Comments (0)

Top reviewers you may like:

Q: Is this a cell balancing board?

Asked by frits on 2020-08-15 03:20:30

1nformatica Yes. The description says "Balanced current: 60mA". If you look there is also a picture showing the balance circuit outlined in red.

2020-08-15 03:42:22 Helpful (0)
Submit
Answers (1)
1nformatica 2020-08-10 04:25:54
0
Recommendations
Comments (0)

Top reviewers you may like:

Q: what type of connector is it

Asked by BG101206368 on 2020-08-04 05:14:47

1nformatica The ESC connector is XT60.

2020-08-06 05:25:20 Helpful (0)
Submit
Answers (1)
1nformatica 2020-07-28 04:37:07
0
Recommendations
Comments (0)

Top reviewers you may like:

1nformatica The power supply must be 12 volts at a minimum of 2 Amps.Be sure to use a quality USB memory stick, the board may not read unbranded ones.

2020-07-28 01:45:37 Helpful (1)
Submit
Answers (1)
1nformatica 2020-07-24 04:24:21
1
Recommendations
Comments (0)

Top reviewers you may like:

Q: se puede usar con este modelo? LP150X08-TLA2

Asked by BG141418191 on 2020-07-20 05:16:37

1nformatica Hola, Sí, puedes usar ese panel. Vea la especificación aquí: panelook punto com Voltaje del panel de 3.3 voltios con conector LVDS de 30 pines. Es una pantalla muy antigua de solo 1024 * 768 de resolución, probablemente pueda encontrar una mejor en una pantalla rota o computadora portátil. Si mira el video en la descripción del producto, puede cambiar los subtítulos al Español. Un saludo desde Andalucia!

2020-07-21 02:58:22 Helpful (1)
Submit
Answers (1)

Q: Where can I buy the airframe?

Asked by 1nformatica on 2020-06-20 02:43:35

cilia no idea.

2020-07-03 10:57:47 Helpful (0)
Submit
Answers (1)
1nformatica 2020-06-23 04:13:54
0
Recommendations
Comments (2)

Top reviewers you may like:

1nformatica 2020-02-19 02:19:40
2
Recommendations
Comments (0)

Top reviewers you may like:

Q: how is the waste solder cleared out?

Asked by joblow on 2020-06-03 09:23:12

1nformatica Unscrew the large knurled ring that secures the heating element to the body. The solder debris may then be easily scraped out. There is a video review in the customer reviews section of the product description.

2020-06-03 09:32:57 Helpful (0)
Submit
Answers (3)

Q: Are replacement blades available?

Asked by 1nformatica on 2020-05-29 07:14:58

Mileaf can't find any blades on banggood

2020-06-02 08:53:43 Helpful (1)
Submit
Answers (1)

Q: What size is the servo JST connector, 1.0 or 1.25? Thanks!

Asked by 1nformatica on 2020-03-10 06:00:42

Laurie 1.25mm - the battery connector is the one that is 2.0.

2020-05-31 09:31:11 Helpful (1)
Submit
Answers (2)